Rechercher une page de manuel
keepalived.conf
Langue: en
Version: 327032 (ubuntu - 08/07/09)
Section: 5 (Format de fichier)
Sommaire
NAME
/etc/keepalived/keepalived.conf - configuration file for keepalivedDESCRIPTION
keepalived.conf is the configuration file which describes all the keepalived keywords. keywords are placed in hierachies of blocks (and subblocks), each layer being delimited by '{' and '}' pairs.Comments start with '#' or '!' to the end of the line and can start anywhere in a line.
TOP HIERACHY
GLOBAL CONFIGURATION
VRRPD CONFIGURATION
LVS CONFIGURATION
GLOBAL CONFIGURATION
contains subblocks of Global definitions and Static routesGlobal definitions
global_defs # Block id
{
notification_email # To:
{
admin@example1.com
...
}
# From: from address that will be in header
notification_email_from admin@example.com
smtp_server 127.0.0.1 # IP
smtp_connect_timeout 30 # integer, seconds
router_id my_hostname # string identifying the machine,
# (doesn't have to be hostname).
}
Static routes/addresses
keepalived can configure static addresses and routes with ip (ie if addresses are not already on the machine). These addresses are NOT moved by vrrpd, they stay on the machine. If you already have IPs and routes on your machines and your machines can ping each other, you don't need this section.
The whole string is fed to ip addr add. You can truncate the string anywhere you like and let ip addr add use defaults for the rest of the string. If you just feed the string "192.168.1.1", the IP will be 192.168.1.1/32, which you probably don't want. This is different to ifconfig which will configure the IP with the standard class, here 192.168.1.1/24. The minimum string then would be the IP/netmask, eg 192.168.1.1/24
static_ipaddress
{
192.168.1.1/24 brd + dev eth0 scope global
...
}
The whole string is fed to ip route add. You can truncate the string allowing ip route add to use defaults.
static_routes
{
src $SRC_IP to $DST_IP dev $SRC_DEVICE
...
src $SRC_IP to $DST_IP via $GW dev $SRC_DEVICE
}
VRRPD CONFIGURATION
contains subblocks of VRRP synchronization group(s) and VRRP instance(s)VRRP synchronization group(s)
#string, name of group of IPs that failover together
vrrp_sync_group VG_1 {
group {
inside_network # name of vrrp_instance (below)
outside_network # One for each moveable IP.
...
}
# notify scripts and alerts are optional
#
# filenames of scripts to run on transitions
# can be unquoted (if just filename)
# or quoted (if has parameters)
# to MASTER transition
notify_master /path/to_master.sh
# to BACKUP transition
notify_backup /path/to_backup.sh
# FAULT transition
notify_fault "/path/fault.sh VG_1"
# for ANY state transition.
# "notify" script is called AFTER the
# notify_* script(s) and is executed
# with 3 arguments provided by keepalived
# (ie don't include parameters in the notify line).
# arguments
# $1 = "GROUP"|"INSTANCE"
# $2 = name of group or instance
# $3 = target state of transition
# ("MASTER"|"BACKUP"|"FAULT")
notify /path/notify.sh
# Send email notifcation during state transition,
# using addresses in global_defs above.
smtp_alert
}
VRRP instance(s)
describes the moveable IP for each instance of a group in vrrp_sync_group. Here are described two IPs (on inside_network and on outside_network), on machine "my_hostname", which belong to the group VG_1 and which will transition together on any state change.
#You will need to write another block for outside_network.
vrrp_instance inside_network {
# Initial state, MASTER|BACKUP
# As soon as the other machine(s) come up,
# an election will be held and the machine
# with the highest "priority" will become MASTER.
# So the entry here doesn't matter a whole lot.
state MASTER
# interface for inside_network, bound by vrrp
interface eth0
# Ignore VRRP interface faults (default unset)
dont_track_primary
# optional, monitor these as well.
# go to FAULT state if any of these go down.
track_interface {
eth0
eth1
...
}
#default IP for binding vrrpd is the primary IP
#on interface. If you want to hide location of vrrpd,
#use this IP as src_addr for multicast vrrp packets.
#(since it's multicast, vrrpd will get the reply
#packet no matter what src_addr is used).
#optional
mcast_src_ip <IPADDR>
# Binding interface for lvs syncd
lvs_sync_daemon_interface eth1
# delay for gratuitous ARP after transition to MASTER
garp_master_delay 10 # secs, default 5
# arbitary unique number 0..255
# used to differentiate multiple instances of vrrpd
# running on the same NIC (and hence same socket).
virtual_router_id 51
# for electing MASTER, highest priority wins.
# to be MASTER, make 50 more than other machines.
priority 100
# VRRP Advert interval, secs (use default)
advert_int 1
authentication { # Authentication block
# PASS||AH
# PASS - Simple Passwd (suggested)
# AH - IPSEC (not recommended))
auth_type PASS
# Password for accessing vrrpd.
# should be the same for all machines.
auth_pass 1234
#addresses add|del on change to MASTER, to BACKUP.
#With the same entries on other machines,
#the opposite transition will be occuring.
virtual_ipaddress {
<IPADDR>/<MASK> brd <IPADDR> dev <STRING> scope <SCOPE> label <LABEL>
192.168.200.17/24 dev eth1
192.168.200.18/24 dev eth2 label eth2:1
}
#VRRP IP excluded from VRRP
#optional.
#For cases with large numbers (eg 200) of IPs
#on the same interface. To decrease the number
#of packets sent in adverts, you can exclude
#most IPs from adverts.
#The IPs are add|del as for virtual_ipaddress.
virtual_ipaddress_excluded {
<IPADDR>/<MASK> brd <IPADDR> dev <STRING> scope <SCOPE>
<IPADDR>/<MASK> brd <IPADDR> dev <STRING> scope <SCOPE>
...
}
# routes add|del when changing to MASTER, to BACKUP
virtual_routes {
# src <IPADDR> [to] <IPADDR>/<MASK> via|gw <IPADDR> dev <STRING> scope <SCOPE> tab
src 192.168.100.1 to 192.168.109.0/24 via 192.168.200.254 dev eth1
192.168.110.0/24 via 192.168.200.254 dev eth1
192.168.111.0/24 dev eth2
192.168.112.0/24 via 192.168.100.254
}
# VRRP will normally preempt a lower priority
# machine when a higher priority machine comes
# online. "nopreempt" allows the lower priority
# machine to maintain the master role, even when
# a higher priority machine comes back online.
# NOTE: For this to work, the initial state of this
# entry must be BACKUP.
nopreempt
# Seconds after startup until preemption
# (if not disabled by "nopreempt").
# Range: 0 (default) to 1,000
# NOTE: For this to work, the initial state of this
# entry must be BACKUP.
preempt_delay 300 # waits 5 minutes
# Debug level, not implemented yet.
debug
# notify scripts, alert as above
notify_master <STRING>|<QUOTED-STRING>
notify_backup <STRING>|<QUOTED-STRING>
notify_fault <STRING>|<QUOTED-STRING>
notify <STRING>|<QUOTED-STRING>
smtp_alert
}
LVS CONFIGURATION
contains subblocks of Virtual server group(s) and Virtual server(s)The subblocks contain arguments for ipvsadm(8). A knowlege of ipvsadm(8) will be helpful here.
Virtual server group(s)
# optional
# this groups allows a service on a real_server
# to belong to multiple virtual services
# and to be only health checked once.
# Only for very large LVSs.
virtual_server_group <STRING> {
#VIP port
<IPADDR> <PORT>
<IPADDR> <PORT>
...
#
# <IPADDR RANGE> has the form
# XXX.YYY.ZZZ.WWW-VVV eg 192.168.200.1-10
# range includes both .1 and .10 address
<IPADDR RANGE> <PORT># VIP range VPORT
<IPADDR RANGE> <PORT>
...
fwmark <INT> # fwmark
fwmark <INT>
... }
Virtual server(s)
A virtual_server can be a declaration of one of
- vip vport (IPADDR PORT pair)
- fwmark <INT>
- (virtual server) group <STRING>
#setup service
virtual_server IP port |
virtual_server fwmark int |
virtual_server group string
{
# delay timer for service polling
delay_loop <INT>
# LVS scheduler
lb_algo rr|wrr|lc|wlc|lblc|sh|dh
# LVS forwarding method
lb_kind NAT|DR|TUN
# LVS persistence timeout, sec
persistence_timeout <INT>
# LVS granularity mask (-M in ipvsadm)
persistence_granularity <NETMASK>
# Only TCP is implemented
protocol TCP
# If VS IP address is not set,
# suspend healthchecker's activity
ha_suspend
# VirtualHost string for HTTP_GET or SSL_GET
# eg virtualhost www.firewall.loc
virtualhost <STRING>
# setup realserver(s)
# RS to add when all realservers are down
sorry_server <IPADDR> <PORT>
# one entry for each realserver
real_server <IPADDR> <PORT>
{
# relative weight to use, default: 1
weight <INT>
# Set weight to 0
# when healthchecker detects failure
inhibit_on_failure
# Script to launch when healthchecker
# considers service as up.
notify_up <STRING>|<QUOTED-STRING>
# Script to launch when healthchecker
# considers service as down.
notify_down <STRING>|<QUOTED-STRING>
# pick one healthchecker
# HTTP_GET|SSL_GET|TCP_CHECK|SMTP_CHECK|MISC_CHECK
# HTTP and SSL healthcheckers
HTTP_GET|SSL_GET
{
# A url to test
# can have multiple entries here
url {
#eg path / , or path /mrtg2/
path <STRING>
# healthcheck needs status_code
# or status_code and digest
# Digest computed with genhash
# eg digest 9b3a0c85a887a256d6939da88aabd8cd
digest <STRING>
# status code returned in the HTTP header
# eg status_code 200
status_code <INT>
}
#IP, tcp port for service on realserver
connect_port <PORT>
bindto <IPADDR>
# Timeout connection, sec
connect_timeout <INT>
# number of get retry
nb_get_retry <INT>
# delay before retry
delay_before_retry <INT>
} #HTTP_GET|SSL_GET
#TCP healthchecker (bind to IP port)
TCP_CHECK
{
connect_port <PORT>
bindto <IPADDR>
connect_timeout <INT>
} #TCP_CHECK
# SMTP healthchecker
SMTP_CHECK
{
# An optional host interface to check.
# If no host directives are present, only
# the ip address of the real server will
# be checked.
host {
# IP address to connect to
connect_ip <IP ADDRESS>
# Optional port to connect to if not
# the default of 25
connect_port <PORT>
# Optional interface to use to
# originate the connection
bindto <IP ADDRESS>
}
# Connection and read/write timeout
# in seconds
connect_timeout <INTEGER>
# Number of times to retry a failed check
retry <INTEGER>
# Delay in seconds before retrying
delay_before_retry <INTEGER>
# Optional string to use for the smtp HELO request
helo_name <STRING>|<QUOTED-STRING>
} #SMTP_CHECK
#MISC healthchecker, run a program
MISC_CHECK
{
# External system script or program
misc_path <STRING>|<QUOTED-STRING>
# Script execution timeout
misc_timeout <INT>
# If set, exit code from healthchecker is used
# to dynamically adjust the weight as follows:
# exit status 0: svc check success, weight
# unchanged.
# exit status 1: svc check failed.
# exit status 2-255: svc check success, weight
# changed to 2 less than exit status.
# (for example: exit status of 255 would set
# weight to 253)
misc_dynamic
}
} # realserver defn
} # virtual service
AUTHOR
Joseph Mack.
Information derived from doc/keepalived.conf.SYNOPSIS, doc/samples/keepalived.conf.* and Changelog by Alexandre Cassen for keepalived-1.1.4, and from HOWTOs by Adam Fletcher and Vince Worthington.
SEE ALSO
ipvsadm(8), ip --help.Contenus ©2006-2024 Benjamin Poulain
Design ©2006-2024 Maxime Vantorre